Assembling the Piano6. Then, fasten it to the pedal board from the back using
screws B (4 x 20 mm).
* 5 1 0 0 0 5 2 9 0 0 - 0 1 *
Screw B
• To assure that assembly is carried out properly, make sure to read these instructions before you begin the assembly. Please keep these instructions
close at hand, so you can refer to them whenever you need.
• To move the piano, lift it carefully—all the while keeping it level.
• Be careful not to pinch your hands or drop this unit on your foot during assembly or transport.
• Make sure to enlist the help of at least one other person when assembling this unit and moving it to a di erent location.
4. Connect the AC adaptor to the DC In jack on the back of the piano, and connect the pedal cord to the Pedal connector. As needed, use the coated clip on the bottom of the piano to fasten the power cord and the pedal cord.
• Make sure to keep screws and any other small parts in a safe location that is out of the reach of small children, so such small parts won’t accidentally get swallowed. • All screws should be tightened provisionally rst, then tightened later. To tighten a screw provisionally, screw it in until about half of its length is no longer visible. Do not use an electric screwdriver when tightly securing the screws. Otherwise, you risk stripping the threads.
* The screwdriver needed to perform the assembly is not supplied. You’ll need to have ready a Phillips screwdriver that matches the size of the screws.
* After rmly tightening all the screws, place the unit at a location that is level and sure to remain stable. The unit must never be placed on top of deep-pile carpet. Otherwise, you risk causing damage to the pedals due to instability and unnecessary movement.
* The surface of the piano unit and the stand are very delicate; handle with care to avoid scratching them.
* Do not place the piano unit directly on the oor. Doing so will damage the bottom panel case and the connectors and holders on the bottom of the piano. Check the Parts
Screw A
7. Go around and tighten all the screws, while at the same time correcting the orientation of any piece that needs it, until everything ts together properly.
* When attaching the rear board, before tightening the screws, adjust things as necessary at all the points where there are screws so as to assure that the rear board is aligned in parallel with the pedal board.
2. Assembling the Piano
Coated clip
5. Use screws E (4 x 16 mm) to fasten the headphone hook.
1
2
3
4
5
6
1 Music rest
2 Piano main unit 3 Side board (left) 4 Side board (right) 5 Rear board
6 Pedal board
A B C
D E
F
Screw (4 x 14 mm): 2 pcs. Screw (4 x 20 mm): 4 pcs.
Screw (5 x 40 mm): 4 pcs.
Screw (5 x 20 mm): 2 pcs. Screw (4 x 16 mm): 2 pcs.
Headphone hook: 1 pcs.
1. Align the screws on the bottom of the piano (one each at left and right) with the metal brackets on the side boards, and while keeping the front of the piano slightly raised, pull it toward yourself to engage the screws in the metal brackets.
* When handling the piano, rmly grasp it. Be careful, so you do not get your ngers pinched.
2. Fasten the piano to the stand with the screw D (5 x 20 mm).
Screw E (2 pcs.)
1. Stand Assembly
* At rst, assemble the entire stand in a temporary fashion, without really tightening the screws. Then, after checking the overall alignment of the boards (and gently shifting certain parts where
3. With the help of another person, raise the left and right side
boards to an upright position.
* Take care that the pedal boards are not twisted.
Screw D
Please don’t get your
ngers pinched.
Screw D
6. Connect the supplied AC adaptor and power cord. Power cord
To AC outlet
necessary), go around and tightly fasten each of the screws. * If necessary, spread out a blanket or similar material to prevent the stand or oor from being scratched during assembly.
* Be careful not to pinch the pedal cord during assembly. 1. As shown in the illustration, place the left and right side boards on the pedal board so that the metal brackets are on the inside, and fasten them provisionally using screws C (5 x 40 mm).
2. Hand-tighten screws C (four locations), and then use a screwdriver to tighten them securely.
* When attaching the pedal board, do not allow any gap to remain between the side board and pedal board when the pieces are assembled.
Side
boardDon’t allow a
4. Place the rear board as shown below and adjust the screw holes of the rear board and the pedal board.
* If you have di culty inserting the rear board, loosen screws C so it is easier to position the rear board in the stand.
The wood grain should face forwards.
Pull the piano toward yourself while
keeping the front slightly raised.
3. Loosen the music rest screws slightly (2–3 mm), insert the music rest brackets between the screws and the body of the piano, and turn the screws to secure the music rest while using one hand to support the music rest.
Place the AC adaptor so the side with the indicator faces upwards and the side with textual information faces downwards. The indicator will light when you plug the AC adaptor into an AC outlet.
7. Adjust the Adjuster.
Turn the adjuster to lower it until the adjuster is in rm contact with the oor. In particular, when you’ve placed the piano on carpet, you must turn the adjuster until it is pressing rmly against the oor.
Adjuster
gap!
Screw C (2 pcs.)
* The pedal may be damaged if there is a gap between the adjuster and the oor.
Leave the pedal cord extended Screw C (2 pcs.)
5. Attach the rear board to the metal parts on the side boards from the front using screws A (4 x 14 mm).
For clamping the rear board, press each upper portion of both side boards.
When attaching the music rest, make sure that it is rmly inserted all the way toward the back, and use your hand to support the music rest so that it does not fall. Also take care not to pinch your hand.
* Do not apply excessive force to the music rest.
* If you need to remove the music rest, loosen the screws while using one hand to support the music rest. Detach the music rest, and then rmly retighten the screws.
When moving the unit
If you need to move the unit, you must rst detach the music rest, close the keyboard cover, disconnect the AC adaptor, and raise the stand adjuster. With at least one other person helping you, lift the unit horizontally and carry it, taking care not to pinch your hands or drop the unit on your feet.
1
Copyright© 2016 ROLAND CORPORATION
Komentar
Posting Komentar